Product variety and just-in-time conflict and challenge

This paper addresses the question of how just-in-time can be implemented within high variety manufacture. To illustrate some of the principles in relation to the high variety-low volume situation the case of a computer manufacturer is considered in detail. For contrast the paper also considers the case of the manufacture of highly-configured four wheel drive vehicles where both variety and volumes are high. The most important issue in high variety/low volume production is that JIT operation should be seen in terms of the tactical holding of inventory in upstream buffers within the supply chain so that value is not added to work in progress prematurely. Tactical buffers ensure that service levels are maintained and the risk of stock-outs is minimized. In high variety/high volume production schedule integrity is the key factor, unreliable schedules being a major inhibitor to the introduction of JIT.

Impact of just-in-time on job content, employee attitudes and well-being:a longitudinal study

Just-in-time (JIT) production systems are increasingly being seen as a vital way for manufacturing organizations to enhance their competitiveness. A number of commentators have suggested that this will simplify jobs and reduce employee well-being. This paper presents a conceptual framework for interpreting the effects of JIT and reports findings from a study of the impact of JIT on the content of workers'jobs and on job satisfaction and psychological strain. The introduction of JIT led to a reduction in control over work timing, an increase in production pressure, and a drop in job satisfaction. Contrary to claims in the literature, no changes were found in control over work methods, other aspects of cognitive demands and skill use, and in psychological strain. The study shows that JIT can be implemented without radical changes in job content or adverse impact in terms of employee strain, and the implications of these findings are discussed.

Setting parameters in MRP for the effective management of bought-out inventory in a JIT assembly environment

In recent years, UK industry has seen an explosive growth in the number of `Computer Aided Production Management' (CAPM) system installations. Of the many CAPM systems, materials requirement planning/manufacturing resource planning (MRP/MRPII) is the most widely implemented. Despite the huge investments in MRP systems, over 80 percent are said to have failed within 3 to 5 years of installation. Many people now assume that Just-In-Time (JIT) is the best manufacturing technique. However, those who have implemented JIT have found that it also has many problems. The author argues that the success of a manufacturing company will not be due to a system which complies with a single technique; but due to the integration of many techniques and the ability to make them complement each other in a specific manufacturing environment. This dissertation examines the potential for integrating MRP with JIT and Two-Bin systems to reduce operational costs involved in managing bought-out inventory. Within this framework it shows that controlling MRP is essential to facilitate the integrating process. The behaviour of MRP systems is dependent on the complex interactions between the numerous control parameters used. Methodologies/models are developed to set these parameters. The models are based on the Pareto principle. The idea is to use business targets to set a coherent set of parameters, which not only enables those business targets to be realised, but also facilitates JIT implementation. It illustrates this approach in the context of an actual manufacturing plant - IBM Havant. (IBM Havant is a high volume electronics assembly plant with the majority of the materials bought-out). The parameter setting models are applicable to control bought-out items in a wide range of industries and are not dependent on specific MRP software. The models have produced successful results in several companies and are now being developed as commercial products.

Introduction : the role of quality, production and technological innovation in improving competitive performance

Quality, production and technological innovation management rank among the most important matters of concern to modern manufacturing organisations. They can provide companies with the decisive means of gaining a competitive advantage, especially within industries where there is an increasing similarity in product design and manufacturing processes. The papers in this special issue of International Journal of Technology Management have all been selected as examples of how aspects of quality, production and technological innovation can help to improve competitive performance. Most are based on presentations made at the UK Operations Management Association's Sixth International Conference held at Aston University at which the theme was 'Getting Ahead Through Technology and People'. At the conference itself over 80 papers were presented by authors from 15 countries around the world. Among the many topics addressed within the conference theme, technological innovation, quality and production management emerged as attracting the greatest concern and interest of delegates, particularly those from industry. For any new initiative to be implemented successfully, it should be led from the top of the organization. Achieving the desired level of commitment from top management can, however, be a difficulty. In the first paper of this issue, Mackness investigates this question by explaining how systems thinking can help. In the systems approach, properties such as 'emergence', 'hierarchy', 'commnication' and 'control' are used to assist top managers in preparing for change. Mackness's paper is then complemented by Iijima and Hasegawa's contribution in which they investigate the development of Quality Information Management (QIM) in Japan. They present the idea of a Design Review and demonstrate how it can be used to trace and reduce quality-related losses. The next paper on the subject of quality is by Whittle and colleagues. It relates to total quality and the process of culture change within organisations. Using the findings of investigations carried out in a number of case study companies, they describe four generic models which have been identified as characterising methods of implementing total quality within existing organisation cultures. Boaden and Dale's paper also relates to the management of quality, but looks specifically at the construction industry where it has been found there is still some confusion over the role of Quality Assurance (QA) and Total Quality Management (TQM). They describe the results of a questionnaire survey of forty companies in the industry and compare them to similar work carried out in other industries. Szakonyi's contribution then completes this group of papers which all relate specifically to the question of quality. His concern is with the two ways in which R&D or engineering managers can work on improving quality. The first is by improving it in the laboratory, while the second is by working with other functions to improve quality in the company. The next group of papers in this issue all address aspects of production management. Umeda's paper proposes a new manufacturing-oriented simulation package for production management which provides important information for both design and operation of manufacturing systems. A simulation for production strategy in a Computer Integrated Manufacturing (CIM) environment is also discussed. This paper is then followed by a contribution by Tanaka and colleagues in which they consider loading schedules for manufacturing orders in a Material Requirements Planning (MRP) environment. They compare mathematical programming with a knowledge-based approach, and comment on their relative effectiveness for different practical situations. Engstrom and Medbo's paper then looks at a particular aspect of production system design, namely the question of devising group working arrangements for assembly with new product structures. Using the case of a Swedish vehicle assembly plant where long cycle assembly work has been adopted, they advocate the use of a generally applicable product structure which can be adapted to suit individual local conditions. In the last paper of this particular group, Tay considers how automation has affected the production efficiency in Singapore. Using data from ten major industries he identifies several factors which are positively correlated with efficiency, with capital intensity being of greatest interest to policy makers. The two following papers examine the case of electronic data interchange (EDI) as a means of improving the efficiency and quality of trading relationships. Banerjee and Banerjee consider a particular approach to material provisioning for production systems using orderless inventory replenishment. Using the example of a single supplier and multiple buyers they develop an analytical model which is applicable for the exchange of information between trading partners using EDI. They conclude that EDI-based inventory control can be attractive from economic as well as other standpoints and that the approach is consistent with and can be instrumental in moving towards just-in-time (JIT) inventory management. Slacker's complementary viewpoint on EDI is from the perspective of the quality relation-ship between the customer and supplier. Based on the experience of Lucas, a supplier within the automotive industry, he concludes that both banks and trading companies must take responsibility for the development of payment mechanisms which satisfy the requirements of quality trading. The three final papers of this issue relate to technological innovation and are all country based. Berman and Khalil report on a survey of US technological effectiveness in the global economy. The importance of education is supported in their conclusions, although it remains unclear to what extent the US government can play a wider role in promoting technological innovation and new industries. The role of technology in national development is taken up by Martinsons and Valdemars who examine the case of the former Soviet Union. The failure to successfully infuse technology into Soviet enterprises is seen as a factor in that country's demise, and it is anticipated that the newly liberalised economies will be able to encourage greater technological creativity. This point is then taken up in Perminov's concluding paper which looks in detail at Russia. Here a similar analysis is made of the concluding paper which looks in detail at Russia. Here a similar analysis is made of the Soviet Union's technological decline, but a development strategy is also presented within the context of the change from a centralised to a free market economy. The papers included in this special issue of the International Journal of Technology Management each represent a unique and particular contribution to their own specific area of concern. Together, however, they also argue or demonstrate the general improvements in competitive performance that can be achieved through the application of modern principles and practice to the management of quality, production and technological innovation.

Modular system design and control for flexible assembly

Flexible Assembly Systems (FASs) are normally associated with the automatic, or robotic, assembly of products, supported by automated material handling systems. However, manual assembly operations are still prevalent within many industries, where the complexity and variety of products prohibit the development of suitable automated assembly equipment. This article presents a generic model for incorporating flexibility into the design and control of assembly operations concerned with high variety/low volume manufacture, drawing on the principles for Flexible Manufacturing Systems (FMS) and Just-in-Time (JIT) delivery. It is based on work being undertaken in an electronics company where the assembly operations have been overhauled and restructured in response to a need for greater flexibility, shorter cycle times and reduced inventory levels. The principles employed are in themselves not original. However, the way they have been combined and tailored has created a total manufacturing control system which represents a new concept for responding to demands placed on market driven firms operating in an uncertain environment.

Experiments in time:exploring the components of motor timing behaviour in dyslexia

This investigation aimed to pinpoint the elements of motor timing control that are responsible for the increased variability commonly found in children with developmental dyslexia on paced or unpaced motor timing tasks (Chapter 3). Such temporal processing abilities are thought to be important for developing the appropriate phonological representations required for the development of literacy skills. Similar temporal processing difficulties arise in other developmental disorders such as Attention Deficit Hyperactivity Disorder (ADHD). Motor timing behaviour in developmental populations was examined in the context of models of typical human timing behaviour, in particular the Wing-Kristofferson model, allowing estimation of the contribution of different timing control systems, namely timekeeper and implementation systems (Chapter 2 and Methods Chapters 4 and 5). Research examining timing in populations with dyslexia and ADHD has been inconsistent in the application of stimulus parameters and so the first investigation compared motor timing behaviour across different stimulus conditions (Chapter 6). The results question the suitability of visual timing tasks which produced greater performance variability than auditory or bimodal tasks. Following an examination of the validity of the Wing-Kristofferson model (Chapter 7) the model was applied to time series data from an auditory timing task completed by children with reading difficulties and matched control groups (Chapter 8). Expected group differences in timing performance were not found, however, associations between performance and measures of literacy and attention were present. Results also indicated that measures of attention and literacy dissociated in their relationships with components of timing, with literacy ability being correlated with timekeeper variance and attentional control with implementation variance. It is proposed that these timing deficits associated with reading difficulties are attributable to central timekeeping processes and so the contribution of error correction to timing performance was also investigated (Chapter 9). Children with lower scores on measures of literacy and attention were found to have a slower or failed correction response to phase errors in timing behaviour. Results from the series of studies suggest that the motor timing difficulty in poor reading children may stem from failures in the judgement of synchrony due to greater tolerance of uncertainty in the temporal processing system.

Cortical mechanisms of attention in time:neural correlates of the Lag-1-sparing phenomenon

If humans monitor streams of rapidly presented (approximately 100-ms intervals) visual stimuli, which are typically specific single letters of the alphabet, for two targets (T1 and T2), they often miss T2 if it follows T1 within an interval of 200-500 ms. If T2 follows T1 directly (within 100 ms; described as occurring at 'Lag 1'), however, performance is often excellent: the so-called 'Lag-1 sparing' phenomenon. Lag-1 sparing might result from the integration of the two targets into the same 'event representation', which fits with the observation that sparing is often accompanied by a loss of T1-T2 order information. Alternatively, this might point to competition between the two targets (implying a trade-off between performance on T1 and T2) and Lag-1 sparing might solely emerge from conditional data analysis (i.e. T2 performance given T1 correct). We investigated the neural correlates of Lag-1 sparing by carrying out magnetoencephalography (MEG) recordings during an attentional blink (AB) task, by presenting two targets with a temporal lag of either 1 or 2 and, in the case of Lag 2, with a nontarget or a blank intervening between T1 and T2. In contrast to Lag 2, where two distinct neural responses were observed, at Lag 1 the two targets produced one common neural response in the left temporo-parieto-frontal (TPF) area but not in the right TPF or prefrontal areas. We discuss the implications of this result with respect to competition and integration hypotheses, and with respect to the different functional roles of the cortical areas considered. We suggest that more than one target can be identified in parallel in left TPF, at least in the absence of intervening nontarget information (i.e. masks), yet identified targets are processed and consolidated as two separate events by other cortical areas (right TPF and PFC, respectively).

Accurate modelling of pulse transformation by adjustable-in-time medium parameters

A possibility of a strong change of an electromagnetic signal by a short sequence of time cycles of pulses that modulate the medium parameters is shown. The backward wave is demonstrated to be an inevitable result of the medium time change. Dependence of the relation between backward and forward waves on the parameters of the medium modulation is investigated. The finite statistical complexity of the electromagnetic signal transformed by a finite sequence of modulating cycles is calculated. Increase of the complexity with the number of cycles is shown.

Visualising and controlling the flow in biomolecular systems at and between multiple scales:from atoms to hydrodynamics at different locations in time and space

A novel framework for modelling biomolecular systems at multiple scales in space and time simultaneously is described. The atomistic molecular dynamics representation is smoothly connected with a statistical continuum hydrodynamics description. The system behaves correctly at the limits of pure molecular dynamics (hydrodynamics) and at the intermediate regimes when the atoms move partly as atomistic particles, and at the same time follow the hydrodynamic flows. The corresponding contributions are controlled by a parameter, which is defined as an arbitrary function of space and time, thus, allowing an effective separation of the atomistic 'core' and continuum 'environment'. To fill the scale gap between the atomistic and the continuum representations our special purpose computer for molecular dynamics, MDGRAPE-4, as well as GPU-based computing were used for developing the framework. These hardware developments also include interactive molecular dynamics simulations that allow intervention of the modelling through force-feedback devices.

Organizations in time:history, theory, methods

Book review: Organizations in Time, edited by R Daniel Wadhwani and Marcelo Bucheli, Oxford University Press, 2014. The title of this edited volume is slightly misleading, as its various contributions explore the potential for more historical analysis in organization studies rather than addressing issues associated with time and organizing. Hopefully this will not distract from the important achievement of this volume—important especially for business historians—in further expanding and integrating business history into management and organization studies. The various contributions, elegantly tied together by R. Daniel Wadhwani and Marcelo Bucheli in their substantial introduction (which, by the way, presents a significant contribution in its own right), opens up new sets of questions, especially in terms of future methodological and theoretical developments in the field. This book also reflects the changing institutional location of business historians, who increasingly make their careers in business schools rather than history departments, especially in Europe, reopening old questions of history as a social science. There have been several calls to teach more history in business education, such as the Carnegie Foundation report (2011) that found undergraduate business education too narrow in focus and highlighted the need to integrate more liberal arts teaching into the curriculum. However, in the contemporary research-driven environment of business and management schools, historical understanding is unlikely to permeate the curriculum if historical analysis cannot first deliver significant theoretical contributions. This is the central theme around which this edited volume revolves, and it marks a milestone in this ongoing debate. (In the spirit of full disclosure, I should add that even though I did not contribute to this volume, I have coauthored with several of its contributors and view this book as central to my current research practice.)

Integrated manufacturing, empowerment, and company performance

There is controversy over whether integrated manufacturing (IM), comprising advanced manufacturing technology, just-in-time inventory control and total quality management, empowers or deskills shop floor work. Moreover, both IM and empowerment are promoted on the assumption that they enhance competitiveness. We examine these issues in a study of 80 manufacturing companies. The extent of use of IM was positively associated with empowerment (i.e., job enrichment and employee skill enhancement), but, with the minor exception of AMT, bore little relationship with subsequent company performance. In contrast, the extent of empowerment within companies predicted the subsequent level of company performance controlling for prior performance, with the effect on productivity mediating that on profit. Copyright © 2004 John Wiley & Sons, Ltd.

Introduction: improving manufacturing performance through technology diffusion, implementation and management

The role of technology management in achieving improved manufacturing performance has been receiving increased attention as enterprises are becoming more exposed to competition from around the world. In the modern market for manufactured goods the demand is now for more product variety, better quality, shorter delivery and greater flexibility, while the financial and environmental cost of resources has become an urgent concern to manufacturing managers. This issue of the International Journal of Technology Management addresses the question of how the diffusion, implementation and management of technology can improve the performance of manufacturing industries. The authors come from a large number of different countries and their contributions cover a wide range of topics within this general theme. Some papers are conceptual, others report on research carried out in a range of different industries including steel production, iron founding, electronics, robotics, machinery, precision engineering, metal working and motor manufacture. In some cases they describe situations in specific countries. Several are based on presentations made at the UK Operations Management Association's Sixth International Conference held at Aston University at which the conference theme was 'Achieving Competitive Edge: Getting Ahead Through Technology and People'. The first two papers deal with questions of advanced manufacturing technology implementation and management. Firstly Beatty describes a three year longitudinal field study carried out in ten Canadian manufacturing companies using CADICAM and CIM systems. Her findings relate to speed of implementation, choice of system type, the role of individuals in implementation, organization and job design. This is followed by a paper by Bessant in which he argues that a more a strategic approach should be taken towards the management of technology in the 1990s and beyond. Also considered in this paper are the capabilities necessary in order to deploy advanced manufacturing technology as a strategic resource and the way such capabilities might be developed within the firm. These two papers, which deal largely with the implementation of hardware, are supplemented by Samson and Sohal's contribution in which they argue that a much wider perspective should be adopted based on a new approach to manufacturing strategy formulation. Technology transfer is the topic of the following two papers. Pohlen again takes the case of advanced manufacturing technology and reports on his research which considers the factors contributing to successful realisation of AMT transfer. The paper by Lee then provides a more detailed account of technology transfer in the foundry industry. Using a case study based on a firm which has implemented a number of transferred innovations a model is illustrated in which the 'performance gap' can be identified and closed. The diffusion of technology is addressed in the next two papers. In the first of these, by Lowe and Sim, the managerial technologies of 'Just in Time' and 'Manufacturing Resource Planning' (or MRP 11) are examined. A study is described from which a number of factors are found to influence the adoption process including, rate of diffusion and size. Dahlin then considers the case of a specific item of hardware technology, the industrial robot. Her paper reviews the history of robot diffusion since the early 1960s and then tries to predict how the industry will develop in the future. The following two papers deal with the future of manufacturing in a more general sense. The future implementation of advanced manufacturing technology is the subject explored by de Haan and Peters who describe the results of their Dutch Delphi forecasting study conducted among a panel of experts including scientists, consultants, users and suppliers of AMT. Busby and Fan then consider a type of organisational model, 'the extended manufacturing enterprise', which would represent a distinct alternative pure market-led and command structures by exploiting the shared knowledge of suppliers and customers. The three country-based papers consider some strategic issues relating manufacturing technology. In a paper based on investigations conducted in China He, Liff and Steward report their findings from strategy analyses carried out in the steel and watch industries with a view to assessing technology needs and organizational change requirements. This is followed by Tang and Nam's paper which examines the case of machinery industry in Korea and its emerging importance as a key sector in the Korean economy. In his paper which focuses on Venezuela, Ernst then considers the particular problem of how this country can address the problem of falling oil revenues. He sees manufacturing as being an important contributor to Venezuela's future economy and proposes a means whereby government and private enterprise can co-operate in development of the manufacturing sector. The last six papers all deal with specific topics relating to the management manufacturing. Firstly Youssef looks at the question of manufacturing flexibility, introducing and testing a conceptual model that relates computer based technologies flexibility. Dangerfield's paper which follows is based on research conducted in the steel industry. He considers the question of scale and proposes a modelling approach determining the plant configuration necessary to meet market demand. Engstrom presents the results of a detailed investigation into the need for reorganising material flow where group assembly of products has been adopted. Sherwood, Guerrier and Dale then report the findings of a study into the effectiveness of Quality Circle implementation. Stillwagon and Burns, consider how manufacturing competitiveness can be improved individual firms by describing how the application of 'human performance engineering' can be used to motivate individual performance as well as to integrate organizational goals. Finally Sohal, Lewis and Samson describe, using a case study example, how just-in-time control can be applied within the context of computer numerically controlled flexible machining lines. The papers in this issue of the International Journal of Technology Management cover a wide range of topics relating to the general question of improving manufacturing performance through the dissemination, implementation and management of technology. Although they differ markedly in content and approach, they have the collective aim addressing the concepts, principles and practices which provide a better understanding the technology of manufacturing and assist in achieving and maintaining a competitive edge.

Canonical solution groups of a homomorphism : manipulator kinematics, nonparametric regression and distributed object systems

The kinematic mapping of a rigid open-link manipulator is a homomorphism between Lie groups. The homomorphisrn has solution groups that act on an inverse kinematic solution element. A canonical representation of solution group operators that act on a solution element of three and seven degree-of-freedom (do!) dextrous manipulators is determined by geometric analysis. Seven canonical solution groups are determined for the seven do! Robotics Research K-1207 and Hollerbach arms. The solution element of a dextrous manipulator is a collection of trivial fibre bundles with solution fibres homotopic to the Torus. If fibre solutions are parameterised by a scalar, a direct inverse funct.ion that maps the scalar and Cartesian base space coordinates to solution element fibre coordinates may be defined. A direct inverse pararneterisation of a solution element may be approximated by a local linear map generated by an inverse augmented Jacobian correction of a linear interpolation. The action of canonical solution group operators on a local linear approximation of the solution element of inverse kinematics of dextrous manipulators generates cyclical solutions. The solution representation is proposed as a model of inverse kinematic transformations in primate nervous systems. Simultaneous calibration of a composition of stereo-camera and manipulator kinematic models is under-determined by equi-output parameter groups in the composition of stereo-camera and Denavit Hartenberg (DH) rnodels. An error measure for simultaneous calibration of a composition of models is derived and parameter subsets with no equi-output groups are determined by numerical experiments to simultaneously calibrate the composition of homogeneous or pan-tilt stereo-camera with DH models. For acceleration of exact Newton second-order re-calibration of DH parameters after a sequential calibration of stereo-camera and DH parameters, an optimal numerical evaluation of DH matrix first order and second order error derivatives with respect to a re-calibration error function is derived, implemented and tested. A distributed object environment for point and click image-based tele-command of manipulators and stereo-cameras is specified and implemented that supports rapid prototyping of numerical experiments in distributed system control. The environment is validated by a hierarchical k-fold cross validated calibration to Cartesian space of a radial basis function regression correction of an affine stereo model. Basic design and performance requirements are defined for scalable virtual micro-kernels that broker inter-Java-virtual-machine remote method invocations between components of secure manageable fault-tolerant open distributed agile Total Quality Managed ISO 9000+ conformant Just in Time manufacturing systems.

Competitive edge through operations management

A view has emerged within manufacturing and service organizations that the operations management function can hold the key to achieving competitive edge. This has recently been emphasized by the demands for greater variety and higher quality which must be set against a background of increasing cost of resources. As nations' trade barriers are progressively lowered and removed, so producers of goods and service products are becoming more exposed to competition that may come from virtually anywhere around the world. To simply survive in this climate many organizations have found it necessary to improve their manufacturing or service delivery systems. To become real ''winners'' some have adopted a strategic approach to operations and completely reviewed and restructured their approach to production system design and operations planning and control. The articles in this issue of the International journal of Operations & Production Management have been selected to illustrate current thinking and practice in relation to this situation. They are all based on papers presented to the Sixth International Conference of the Operations Management Association-UK which was held at Aston University in June 1991. The theme of the conference was "Achieving Competitive Edge" and authors from 15 countries around the world contributed to more than 80 presented papers. Within this special issue five topic areas are addressed with two articles relating to each. The topics are: strategic management of operations; managing change; production system design; production control; and service operations. Under strategic management of operations De Toni, Filippini and Forza propose a conceptual model which considers the performance of an operating system as a source of competitive advantage through the ''operation value chain'' of design, purchasing, production and distribution. Their model is set within the context of the tendency towards globalization. New's article is somewhat in contrast to the more fashionable literature on operations strategy. It challenges the validity of the current idea of ''world-class manufacturing'' and, instead, urges a reconsideration of the view that strategic ''trade-offs'' are necessary to achieve a competitive edge. The importance of managing change has for some time been recognized within the field of organization studies but its relevance in operations management is now being realized. Berger considers the use of "organization design", ''sociotechnical systems'' and change strategies and contrasts these with the more recent idea of the ''dialogue perspective''. A tentative model is suggested to improve the analysis of different strategies in a situation specific context. Neely and Wilson look at an essential prerequisite if change is to be effected in an efficient way, namely product goal congruence. Using a case study as its basis, their article suggests a method of measuring goal congruence as a means of identifying the extent to which key performance criteria relating to quality, time, cost and flexibility are understood within an organization. The two articles on production systems design represent important contributions to the debate on flexible production organization and autonomous group working. Rosander uses the results from cases to test the applicability of ''flow groups'' as the optimal way of organizing batch production. Schuring also examines cases to determine the reasons behind the adoption of ''autonomous work groups'' in The Netherlands and Sweden. Both these contributions help to provide a greater understanding of the production philosophies which have emerged as alternatives to more conventional systems -------for intermittent and continuous production. The production control articles are both concerned with the concepts of ''push'' and ''pull'' which are the two broad approaches to material planning and control. Hirakawa, Hoshino and Katayama have developed a hybrid model, suitable for multistage manufacturing processes, which combines the benefits of both systems. They discuss the theoretical arguments in support of the system and illustrate its performance with numerical studies. Slack and Correa's concern is with the flexibility characteristics of push and pull material planning and control systems. They use the case of two plants using the different systems to compare their performance within a number of predefined flexibility types. The two final contributions on service operations are complementary. The article by Voss really relates to manufacturing but examines the application of service industry concepts within the UK manufacturing sector. His studies in a number of companies support the idea of the ''service factory'' and offer a new perspective for manufacturing. Harvey's contribution by contrast, is concerned with the application of operations management principles in the delivery of professional services. Using the case of social-service provision in Canada, it demonstrates how concepts such as ''just-in-time'' can be used to improve service performance. The ten articles in this special issue of the journal address a wide range of issues and situations. Their common aspect is that, together, they demonstrate the extent to which competitiveness can be improved via the application of operations management concepts and techniques.

A design and implementation methodology for high variety electronics assembly systems

Small indigenous manufacturers of electronic equipment are coming under increasingly severe pressure to adopt a strong defensive position against large multinational and Far Eastern companies. A common response to this threat has been for these firms to adopt a 'market driven' business strategy based on quality and customer service, rather than a 'technology led' strategy which uses technical specification and price to compete. To successfully implement this type of strategy there is a need for production systems to be redesigned to suit the new demands of marketing. Increased range and fast response require economy of scope rather t ban economy or scale while the organisation's culture must promote quality and process consciousness. This paper describes the 'Modular Assembly Cascade' concept which addresses these needs by applying the principles of flexible manufacturing (FMS) and just in time (,JlT) to electronics assembly. A methodology for executing the concept is also outlined. This is called DRAMA (Design Houtirw !'or· Adopting Modular Assembly).